HARMAN KARDON BETATENDVC
Manual de Servicio

BETA TEN.DVC 2-OHM (PARALLEL) WIRING
Beta Ten.dvc
(rear view)

BETA TEN.DVC DUAL-SUBWOOFER WIRING
(Dual) Beta Ten.dvc
(rear view)

Ten.dvc 10" S u b w o o f e r

INSTRUCTIONS
CAR AUDIO
+
®

+ �+ From

+

�

+ From Amp Output �

+
®

�

�

®

Amp Output � � +

�

+

�

+

METHOD #1

Thank you for purchasing an Infinity Beta Ten.dvc 10" Dual Voice-Coil Subwoofer. You�ve selected a premium product that offers superior performance and advanced materials, resulting from over 25 years of loudspeaker design. This Infinity product is made with our ongoing dedication to create the best consumer audio products possible. As a result, you can expect your new Beta Subwoofer to provide you with many years of listening enjoyment.

� Locate and note all fuel lines, hydraulic brake lines, and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. � Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws.

THIELE-SMALL PARAMETERS
FREE-AIR RESONANCE: COMPLIANCE VOLUME: MECHANICAL Q: ELECTRICAL Q: TOTAL Q: MAXIMUM EXCURSION: VOICE COIL DC RESISTANCE: FS (HZ) VAS (FT3) VAS (LITERS) Q
MS

(Dual) Beta Ten.dvc
(rear view)

Refer to Subwoofer Enclosure Trade-Offs (on the inside pages) for help in selecting an enclosure type and alignment. Also, review the wiring diagrams (on
+ �

24.00 2.70 77.00 8.08 0.20 0.20

BETA TEN.DVC 8-OHM (SERIES) WIRING
Beta Ten.dvc
(rear view)

+

From Amp Output

+

�

the back page) on how to connect the subwoofer for 2-ohm, 8-ohm, and summed-mono applications. Each Infinity Beta Ten.dvc 10" Dual Voice-Coil Subwoofer is covered by our limited parts and labor warranty (see the enclosed warranty card). Keep your original dated bill of sale in case warranty service is required. IMPORTANT: Installation of automotive stereo components can require extensive experience in dealing with a variety of electrical, and mechanical procedures, including subwoofer box building. Although these instructions explain how to install a Beta Subwoofer in a general sense, they do not show the exact installation methods for your particular vehicle. If you do not have the experience, do not attempt the installation yourself; instead ask your Authorized Infinity Car Audio Dealer about professional installation options.

®

®

QES QTS X
MAX

�

�

+

�

+

+ From Amp Output �

+

� METHOD #2
®

(IN)

0.39 10.00 2.80

XMAX (MM) RE (OHMS)

�

+

IMPORTANT: When connecting two Beta Ten.dvc subwoofers together, use Method #1 to create a net 4-ohm impedance. NEVER USE METHOD #2, since most amplifiers cannot fully control driver movement in this configuration.

SPECIFICATIONS
DIAMETER: POWER HANDLING: FREQUENCY RESPONSE: NOMINAL IMPEDANCE: DIMENSIONS: 10" (254.0 MM) 250 WRMS PER VOICE COIL 20 ~ 500 HZ 4 OHMS PER VOICE COIL SENSITIVITY (2.83 V @ 1 M): 93 dB

BETA TEN.DVC SUMMED-MONO WIRING
Beta Ten.dvc
(rear view)

DECLARATION OF CONFORMITY

� From Left Amp Output + From Right Amp Output + �

+
We, Infinity Systems A/S Kongevejen 194B DK-3460 Birkerød DENMARK declare in own responsibility, that the Beta Ten.dvc subwoofer is in compliance with technical standards EN 50 081-1/1992 and EN 50 082-1/3.1995

PRECAUTIONS
� Always wear protective eyewear when using tools. � Turn off all audio systems and other electrical devices before starting the installation. � Disconnect the (�) negative lead from your vehicle�s battery.
Steen Michaelsen Infinity Systems A/S Birkerød. DENMARK. 4/96

mounting depth 4.75" (120.65 mm)

®

cutout diameter 9.37" (238.00 mm) outer diameter 10.70" (271.78 mm)

�

®

Infinity Systems, Inc. � 20630 Nordhoff Street Chatsworth, CA 91311, USA � VOICE (818) 407- 0228 � FAX (818) 709 -9486
Printed In Japan

®

Infinity Systems, Inc. � 20630 Nordhoff Street Chatsworth, CA 91311, USA � VOICE (818) 407- 0228 � FAX (818) 709 -9486